Used Forklifts Canada - A narrow aisle forklift is utilized for lowering and lifting loaded pallets from high storage spaces. This particular type is recommended for work environments with narrow spaces between aisles, like retail establishments or warehouses. The forklift has small, solid rubber tires that make maneuvering very simple. Usually, the operator of this specific kind of forklift stands up in a small cockpit. The stand-up design enables the narrow aisle forklift to be as short and narrow as possible. A stand-up cockpit forklift normally has three tires: two in the front, and one in the back. This configuration enables for easy and fast maneuvering. There are some models of these forklifts that are available with a sit-down cockpit. The lift attachment could pivot to the sides, allowing the lift to be operated without the operator having to reposition the whole machine. The sit-down version normally has four wheels. An electric engine is utilized to power many narrow aisle forklifts. Electric-powered machines do not produce exhaust fumes and are quiet, making them the suitable alternative for closed areas like for example retail spaces. Some lifts come with a diesel engine or a gas engine. Nevertheless, the diesel version is not recommended for indoor application because it could produce exhaust and be noisy. The forklift is a material handling device utilized to lift and transport loads from one location to another. Each and every forklift part has a particular function. Different parts can be utilized to move the load either horizontally or vertically. The mast refers to all the components which lift and lower the load. There are various types of masts used for raising loads to various heights: duplex, triplex, quad and simplex. There are four various ways you could power a forklift: gas, electric, diesel and propane. The battery is located inside the cab under the seat. The propane tank is situated on the back of the truck. The fuel tank on diesel and gas forklifts is underneath the back of the truck. The cab is situated in the middle of the truck. This is where the operator sits and accesses all the controls and informational gauges. The gas pedal, steering wheel, lifting controls, tilting controls and brake are all located in the cab. The frame of the truck carries all the largest components of the forklift, like the counterweights, which are located at the rear in order to prevent the truck from tipping when loaded. The frame consists of the overhead guard that protects the operator. The undercarriage holds the wheels, driveshaft and axles. Hyster is an industry leader in the materials handling industry that has been in business for over eighty years. However, it began as a manufacturer of lifting equipment and winches. Most of its production was concentrated in the northwest United States and dealt mostly with the timber and logging industry. A couple years after the first forklift trucks were invented Hyster became synonymous with quality production. Over the previous 80 years Hyster has continued to expand and develop its product line. The growth of its products coupled with its wish to stay service oriented has allowed Hyster to grow into the intercontinental participant it is at the moment. All Toyota machines and components manufactured within North America adhere to the International Organization for Standardization or ISO 14001 standard. The Columbus TIEM plant has been honored on many occasions for its devotion to relentless development and its environmentally friendly systems. It is the first and only producer to offer EPA and CARB-certified Compressed Natural Gas powered lift trucks on the market. For example, the Toyota 8-Series IC lift trucks emit 70 percent fewer smog forming emissions than the current centralized EPA standards and have complied with California’s strict emission standards and regulations. The business Jungheinrich is a European leader for system technology and is now a leading producer and worldwide supplier of material flow technology, warehouse technology and lift trucks. The business offers a complete product assortment of material handling equipment and rack systems along with services from a manufacturing logistics service provider. Jungheinrich is the 3rd largest supplier of lift truck trucks used for the materials handling business. They realized their incredible growth due mostly to their quality lift truck designs and innovative technology. They have developed a host of productivity and ergonomic enhancements for their fleet and introduced a proprietary 3-phase AC motor and controller technology. Jungheinrich has over 300 dealer and service facilities strategically located all around Mexico, Canada and the United States. One of the companies main objective is to simplify their customers material handling needs by providing customized solutions. Jungheinrich manufactures a lot of forklifts in their line of products, lift trucks which are intended to work outstandingly in various applications. These machinery are well-suited to complete tasks in a diverse environment. They can do food processing, order picking, stacking and warehousing applications with ease.
Manitou: Manitou Aerial Lifts Canada - Numerous workplace applications would require more reach than the usual job. The articulating and telescopic booms is a great alternative for these particular situations. Bi-energy or electric or engine-powered booms are ideal for rough terrain, outdoor or indoor use, so technically, there is a suitable boom lift available for every kind of task. Just take the time to figure out what kinds of capacities you would require to get the task done and what type of cargo you will be dealing with. As aerial work platforms, the articulating booms use many boom parts that articulate or hinge. These equipment provide a maximum reach of 21 feet 5 inches or 6.25 meters to 21.26 meters or 69 feet 9 inches. These models can vary in height between 36 feet and 11.14 meters or 141 feet or 43.15 meters. Usually, articulated boom models are classified by horizontal reach and by platform height. In order to access work areas over obstacles and barriers including equipment or shelving, the articulating booms are usually used. They have less horizontal outreach than telescopic booms, but the articulating booms offer greater versatility and better positioning. This allows better access for overhead work places from aisles and from congested areas. Throughout the variety of articulating booms, most of them could hold weight capacities of up to 500 pounds or 227 kilograms. These machinery are able to lift 2 operators and their tools easilyand sometimes extra materials. There are both industrial and rough terrain articulating booms, similar to scissor lifts. Industrial units are normally equipped with non-marking tires and are intended for indoor application. The majority of articulated boom manufacturers utilize clean burning fuels such as liquid propane gas or LPG or DC electric power for their industrial models. AC drive system technology is common in industrial forklifts, although it is new to the aerial work platforms market. This technology combines 3-phase AC drive motors together with DC batteries for more continuous control of turning, drive speed and braking and overall energy efficient operation. The rough terrain units have been engineered particularly to work on rugged work sites. These machinery have features like diesel engines, lug-tread tires, an oscillating axle and 4-wheel drive. These are common specialized items utilized on rough-terrain articulating booms. These heavy-duty extras are what make these machinery able to withstand the rough settings they work in.
Hyster: Hyster Deisel Forklifts Canada - Though owning a lift truck is much more commonplace than renting one, the Hyster Company knows that every company has various requirements. This is the reason why your local Hyster dealer has thousands of rental models available for those times when owning the piece of machinery may not be possible or required. These models can be leased on a short term or long term basis depending on your business requirements. Normally, a forklift is temporarily needed when another forklift is being serviced. There might be times when a few rental trucks are needed like when changes in season might change the requirements on your business and storage of additional forklifts for the off-season might not be sensible. Ideally, forklifts will all be equipped with a basic package that could deal with every job. Realistically, this is not the case. The Hyster Special Products Engineering Department, or also referred to as SPED, is committed to customizing each and every lift truck to suit your application requirements. They could equip machines with everything from totally specializing a model to suit a particular job to simple visual and audible warning devices. Whatever the situation, SPED would work with you to get you the lift truck with the tools you require. When adding machinery to your existing line is difficult, your Hyster dealer may be able to help with your financing options. Whether you buy or lease machinery, new or second-hand, Hyster Capital can provide you great service at competitive rates. All our dealers are devoted to finding you the right alternatives at the best value to your business. For your ever-changing application and business needs, your local Hyster dealer is available to help you pick the rental models most appropriate for you.
Trek: Trek Sweepers Canada - TREK Cleaning Machines is a maker of cleaning machinery who have a passion for the cleaning industry. The company's creative nature is a reflection of the business founder's huge entrepreneurial style. Chris Knowlton, Jim Hartsock and Bob O'Hara together have 60 years combined experience in successfully developing, manufacturing, supporting and selling really efficient machinery which provide supreme value to all their clients. TREK is committed to new design ideas and extremely committed to quality. All these corporate values are reflected in their product development and individual machines. TREK Cleaning Machines provides a variety of products that provide reasonable production gains to their clients as well as energize their dealer partners. Energy, commitment and dedication to customer satisfaction resonate with every equipment. Team TREK is keen on dealing with the harder tasks and new challenges. The company is proud to introduce their breakthrough Torsion scrubber line of cleaners. The Torsion vision project developed and was motivated from the company's unique comprehension of operator's skills and needs, specific cleaning applications, and the owner's strong desire to greatly decrease their costs through productivity gains. TREK, along with their dealer-partners are dedicated to having both parts support and technical support whenever you need it. This commitment to providing great service is at the core of their customer service culture. Making certain that your cleaning machinery is up and running on a daily basis is essential to the customers and to TREK as well. The corporation offers industry leading technology in order to deliver reliable equipment to reduce your cleaning expenses. TREK has become a preferred choice for many different businesses. On the market today, there are a lot of manufacturers that spend much effort in developing user-friendly cleaning machines at a great price. In an effort to develop such equipment, TREK Cleaning Machines have been a popular producer of excellent sweepers and scrubbers for many years. Recently, the company launched a full line of industrial floor sweepers and floor scrubbers with a focus on increased production and on extremely competitive pricing. TREK was initially founded by industry veterans. They know the problems and concerns that face manufacturing facilities. The Torsion SUR or Stand- Up Rider Scrubber was made together with the Radial Sweeper. The TREK Torsion SUR is an articulated scrubber machine. This means that it is uniquely made with 2 sections which utilize a pivoting joint to connect them. This specific design allows the Torsion SUR TB6 scrubber to provide a turning freedom of 150 degrees, improved handling, and increased maneuverability. These features as well as the 60-gallon tanks, that come standard equipped, means an increased production of up to 100 percent.
Hyundai: Hyundai Propane Forklifts Canada - Basic Types of Fuels Used for Forklifts Forklifts, also referred to as powered lift trucks, are utilized to perform numerous jobs in construction, distribution and industrial settings. These heavy-duty machinery are intended to be reliable and tough so they can transport heavy items in all different types of conditions and environments. Forklifts are powered by many types of fuels and thus able to adapt to many different work environments. Electricity The electric models generate no emissions and quiet and reliable. These units could operate on industrial-strength large batteries that are made to be able to be successfully recharged about 1500 times in their functional lifespan. Since electric forklifts generate no exhaust fumes, it is oftentimes the machinery of necessity and choice in areas that have inadequate ventilation. These forklifts require a charging place somewhere on the premises which is equipped with an emergency acid spill kit and eyewash station due to the batteries. For safety reasons, the charging area must be well ventilated. Propane Liquid propane is a common power source for the modern forklift. Propane provides different benefits over diesel and electric models. Like for example, propane is normally cheaper than electricity. When the battery is being recharged, there is no need to remove the forklift from service. Propane units also offer a much cleaner operation compared to forklifts which are powered by diesel. In most cases, a propane forklift is refueled by simply changing out the propane tank which is empty with a new one which is full. Usually, an off-site supplier will re-fill the tanks. This ensures an easy, safe and fast re-fueling procedure. Gasoline and Diesel Gasoline and diesel forklifts could require more maintenance and produce a smelly exhaust. They have fairly high fuel costs too. Because they have a useful and much longer lifespan, they are rather dependable compared to propane or electric models. Re-fueling requires a fuel supply on site which follows strict health and safety codes. Gas and diesel models are mostly utilized in outdoor applications on rough terrain, like on construction sites or in lumber yard environments.
Gradall: Gradall Aerial Lifts Canada - Classifications of Aerial Lift Platforms & Scissor Lifts A scissor lift is made up of a series of crisscrossed steel arms which are connected to create an X pattern. When raised vertically, the X pattern of support holds the rectangular platform which is situated on top of the lifting apparatus. There are support railings along the lifting mechanism's edges in order to keep the employees safe and help to secure their tools. The scissor lift has a low profile, best used for smooth surfaces like concrete, pavement and hard dirt surfaces. These equipment use either an electric motor or a combustion engine in order to power the lifting mechanism and move the lift. The operator must move the lift itself if she or he has to travel horizontally, as the lift apparatus just operates the lift in a vertical way. Rough Terrain Scissor Lift The rough terrain scissor lift and the standard scissor lift use the same lifting technology. The key difference is that the rough terrain models feature a different base which is particularly made for uneven surfaces. These models also offer higher ground clearance and oversized all terrain tires. The rough terrain scissor lifts use 4-wheel drive in order to easily navigate through muddy and difficult terrain. Telescopic Boom Lift Telescopic booms are made to be raised both diagonally and vertically. This unit has a small work platform that houses controls to be able to control the boom. The controls work with a combustion engine so as to power the hydraulics which move the lift and power the boom. The telescopic boom lift is an independent lift unit and has off-road capable tires. Articulating Boom Lift There are two telescopic booms on the articulating boom lift. These are attached with a moving elbow mechanism. This lifting machinery has a bucket or a small work platform that is outfitted with hand controls in order to control the boom. These are stand-alone lifts which are powered by a combustion engine. Articulating boom lifts are available with either off-road or hard surface tires. These lifts are made in order to reach on top of and over top of buildings. Aerial Mast Lift The aerial mast lift uses a telescopic mast so as to raise a work platform vertically into the air. Normally, these lifts are electrically powered or pneumatic powered and are self-propelled machines. These equipment offer an ideal solution for working in high racks in narrow warehouse aisles. It is very essential to remember that aerial mast lifts are limited to vertical movement and are not recommended for off-road application.
Mitsubishi: Mitsubishi Large Capacity Forklift Canada - It is quite key for some businesses to examine the method of choosing a forklift. Like for instance, will your company select always the same unit for your warehouse or dock work? If this is so, you might be missing out on a more effective forklift. There can be other models existing on the market which enable more to get accomplished as they offer less fatigue to operators. You might be able to take advantage of loading trailers in a more effective way. By doing some research and evaluation, you can determine if you have the best machinery to meet your needs. By reducing operator fatigue, you can significantly increase your performance. Some of the key factors to think about when determining forklift units which address specific problems consist of: Trailer Loading Frequency: You probably won't require a pricey lift truck to accomplish jobs if your shipping and receiving department loads just a few semi-trailers or box trucks per week. A less expensive walkie-rider or walkie model will be able to deal with the task if: A 4500 to 6000 pound capacity is sufficient and you are not required to stack loads inside the trailer. Last of all, you have to think about whether or not the transition from the dock floor to the dock leveler and into the trailer is not too jarring for the operator because the small load wheels should travel over the dock plate. If on the other hand, your shipping facility is consistently loading trailers, than a stand-up end control will make more sense over a walkie model or a walkie-rider. These battery-powered forklifts easily fit into a standard 108 inch trailer door. Their masts enable in-trailer stacking. These types of forklifts offer a model capacity range from 3000 to 4000 lbs. Operator Duties: For material handling requirements, every business has a slightly different system. Several lift truck operators will normally unload and load products in the shipping department along with storing things on inventory racks, replenish the manufacturing line, handle the paperwork associated with the loads, scan and attach bar codes and other tasks. Usually, the forklift operators who are constantly on and off of their forklifts during their shifts find it less fatiguing and a lot quicker to exit a stand-up control unit, as opposed to a sit down kind.
Tenant: Tenant Sweepers Canada - The Tennant Company is one of the leading forces behind producing, engineering and marketing products that help keep our world cleaner, healthier and safer. The company has a dream to become the global leader in chemical free cleaning solutions as well as other technologies. Tennant takes pride in developing innovative solutions which are changing the way the globe handles its cleaning methods. Tennant's products which have made it to the market to date comprise cleaning equipment that is utilized to clean surfaces both indoors and outdoors. Furthermore, Tennant provides parts, financing, service and equipment for their items. Items are sold under the Green Machines, Tennant, Alfa, Nobles and Orbio brands. A Legacy Built on Advancing the Business During 1870, Tennant Company was founded by George H. Tennant. He started out as a one-man woodworking business which eventually flourished into a successful wood flooring and wood products company. Eventually, Tennant grew into a maker of floor cleaning equipment. Throughout the history of the company, Tennant has remained dedicated and focused on advancing its industry by creating a culture that celebrates innovative ideas and aggressively pursuing new technologies. Presently, Tennant has become a worldwide leader in engineering, marketing and making solutions to help create a safer, cleaner and healthier planet for everyone. In order to be an innovative business, some risks have to be taken. It is essential that somebody becomes a leader and takes a dare. This is the actual mindset behind the Tennant Company, along with the cleaning solutions they make. The client's needs are what continually drive the company to push forward with innovative designs. They tirelessly work to create better ways to get rid of debris, dust and dirt in order to help create a cleaner and therefore healthier planet for everyone to enjoy. The business has changed the cleaning business and the items we have come to rely on. There are new equipment, services and items being made to keep our globe cleaner. Being able to keep our play and work areas really clean, helps keep people healthier. Tennant has different types of products offered for both commercial and residential applications. If you are in the market for some dependable, quality, industrial cleaning machinery, get in touch with your local Tennant dealer today. They have a huge array of brand new, second-hand and refurbished units available to meet your particular application and your specific budget. Be sure to evaluate your requirements, such as how much space you should clean and how often. When you determine all these answers, it would be easier to find a suitable equipment.
Taylor: Taylor Outdoor Forklifts Canada - You would need to establish a budget and account for all the operations you do, when deciding on a brand new or second-hand forklift. It is also important to find the right company for your business to work for. You want to speak with a respectable dealer who will take the time to ask the right questions so as to know how you plan to use the machine before selling you a unit. To be able to find the right machine for your business, the selling company will have to know the types of operations your business performs, and how you intend to use the machinery. As well, they must know your budget so they know how much money you can afford to spend on such a piece of machine. To find the best machine for your price range, you would have to learn about the many companies and what they could provide you. One way to figure out who the right company is by requesting them to send you quotations on the units you are interested. After that, it is better that you speak to roughly 4 and 6 companies in order to find out which ones are selling the right item. It is extremely vital at this time to also find out what specific type of service they provide. When you have short-listed several corporations, you could then request that they deliver their forklift to your location so that you and your workers have a chance to try it out. You could try it out typically for approximately 2 or 4 hours. This should be sufficient time for you to become familiar with the model and decide whether or not it will be right for your jobsite. It provides a great opportunity to test out the basic functionality of the machinery. It is also a great idea to work with corporations who provide a large variety of new and high quality used forklifts. These corporations usually carry a variety of manufacturers' products also to provide their clients maximum choices. Respectable dealers will also provide several good references for you to look at.
Kalmar: Kalmar Counterweight Forklifts Canada - Suggestions for Buying Forklift Components There are a few things that might want to know about before thinking about purchasing parts for your lift truck. Several of the things, they might not tell you otherwise, so it is really a great idea to know about what those tips are so that you could save yourself a lot of money and time in the long-run. In the start, when you initially go searching, you will have to know exactly what size of equipment you need. This would save you a lot of time as you will not have to waste energy returning any items. It is easy to guesstimate and accidentally jump the gun when you require a specific component, therefore, you should know which kind of forklift you have and what things it needs. There is a wide range of locations that sell components for forklifts, so make sure to do some research to find out all the best alternatives for you. Making time to compare prices ahead of time will prepare you for how much you are going to need to spend and get you ready to make the investment. Do some price comparisons to see what stores are offering the best prices, as replacement parts are often expensive. The lift truck is a high maintenance machinery that is worked hard. In order for the model to operate safely and efficiently, it is very important to invest in replacing worn out and broken components as soon as they are discovered. Some individuals even search on the World Wide Web and search for the availability and best pricing that way. There may be a range of locations within your area carrying these components and pricing out ahead of time will save you from driving all around town. If you are unsure of what lift truck parts are needed, find someone who specializes in your specific brand of equipment and allow them to educate you on what components you require. Ask around with those with the same lines of business regarding where and whom they go to shop for components and have maintenance completed. If you have no one to speak with directly, you could always look on blogs and read where others go.
Raymond: Raymond Electric Forklift Canada - Forklift Battery Charging and Safe Installation Batteries used in forklifts are costly pieces of machinery that are pretty large weighing many pounds. The task of charging and installation of these batteries is something which will have to be really planned out in advanced in order to make certain that these procedures can be completed properly and safely. Maintaining proper handling and a sound charging method could majorly increase the regular lifespan of a battery. Standard Charging It is important not to connect the battery to the charger until it is at 20% capacity or less. By charging the battery when it is more than 20 percent, the lifespan of the battery could really be shortened. On around each 5th charge cycle, the charger must be set on the weekend or equalize setting, depending on which type of charger you are using. The cycle of charging must not get interrupted. You must avoid using the battery for some hours when the charge cycle is complete. By practicing these methods, you could help make certain that you get the maximum battery performance available. Charger Maintenance Be certain to have the charger turned off when in the process of hooking up the battery to the charger. Connect the charger to the battery and not the lift truck. This is a common mistake that can inadvertently cause damage to both the forklift and the charger. Additionally, it is very vital that the battery amperage should match that of the charger. Do not ever allow the battery to completely discharge or to deep discharge. This would shorten the battery life greatly and can even prevent the charger from being able to start. If the battery charger reads that there is no activity in the battery, it would not start the charge cycle. If this situation happens, a technician must be called to be able to re-set the charger prior to charge being able to start.
Doosan: Doosan Propane Forklifts Canada - Propane Motor Fuel & Forklift Safety Propane-powered lift trucks are widely utilized in a variety of industries. These lift trucks are usually found in distribution centers and warehouses, along with in both industry and commercial applications. Propane fuel has some unique factors when used in a workplace. It is essential to always follow safety procedures and practices when utilizing this specific machinery. Operation Forklifts are powered electrically, with diesel, propane or with gasoline. Propane powered lift trucks are the most commonly obtained and utilized equipment. You'll notice several reasons for this. Propane is a clean-burning fuel, which means it generates a lot less engine exhaust than gasoline and diesel. Regardless of the type of fuel being utilized to operate the lift truck, smoking must be avoided when operating and the unit must not be used near an open flame. The propane is normally stored in a fuel tank, which should be changed out when empty. It is vital for the operator to check that the tank is securely fastened in place before starting the engine. Fueling Propane is extremely cold and could result in serious burns if it comes in contact with skin. It is vital that safety procedures be followed when changing out an empty tank and when the unit is being refueled. Smoking is forbidden in the fueling area. Fueling must never be carried out near an open flame or ignition source. The operator should put on personal protective equipment when changing or fueling the tank. Full eye protection is really important. Thick gloves should be worn in order to protect the skin from exposure to propane.
Ingersol Rand: Ingersol Rand 4 Wheel Drive Forklift Canada - As the market for rough terrain lift trucks has emerged so has the demand for straight mast forklifts. Their emergence and demand has leveled over the past 10 years thanks to explosion of telescopic handlers. Now, manufacturers of forklifts are focusing their product development on the core function of the forklift. For instance, models that offer a lift capacity of less than 6000 pounds on average are up to 2.45% to a bit more than $46,000. Other kinds of machines within the category's bulk class varying from 6000 pounds to 10,000 pounds in capacity are up 3.15% to $54,177. Buyers of machines would quickly point out only if their real expenses are up ever so slightly. With models which depend on diesel fuel, hourly costs in those 2 classes have risen 81.6% and 84.3% respectively. Even if the prices on the dealer's tag might not seem all that different, once the machinery has left the sales yard and enters the customer's work space, it has to produce on a large scale. The rough-terrain lift truck market has leveled off fast over the past ten years in the wake of the telescopic-handler explosion. The telescopic handlers are may just be the future that this specific kind of machinery is evolving to. The job of a telehandler is to place a load with a long reach. The rough-terrain forklift continues to be the heavyweight champ when it comes to pure grunt lifting. The manufacturer Omega makes a lot of different lines of lift machinery and a whole array of rough-terrain forklifts. The Mega Series is an established line consisting of bigger vertical-mast units. These models provide lifting capacities varying from 8000 pounds all the way up to 20,000 pounds. The next step was to enable lifting capacities up to 50,000 pound and the HERC Series was developed to complete this job. The more complex and bigger machines required, the more specialized that OEMs such as Omega become.
Snorkel: Snorkel Straight Man Lifts Canada - Man Lift Safety Procedures Man lifts are specifically designed aerial platforms used to lift individuals vertically up and down. The man lift is also referred to as a vertical person lift. It is utilized in a variety of industries for many different reasons. Man lifts are potentially very dangerous though they can be really useful. When using one, there are several standard safety measures that should be taken into account when utilizing this specific type of machine. Get Correct Training Before utilizing a man lift, it is necessary to read all available manuals for the machinery. Try to observe someone utilizing the lift several times prior to ever trying to operate it yourself. This presents a great opportunity to ask an experienced operator any general questions and become familiar with the procedures. Watching a qualified person, someone who really knows what they are doing could teach you many good habits right from the start. After the reading and observations are done, make sure the required training is completed successfully. Most businesses would require their operators to receive training from a certified operator. The training program will comprise information on the scope of hazards associated with using the lift, manufacturer operating requirements, hazard precautions, as well as information regarding the rated load capacity, like workers and Materials. Finally, training would include a demonstration of knowledge and skill in how to use the lift properly. Check the Nearby Area It is important to check the location in which the man lift will be used, before operating it. Make certain that the operating surface is free of debris and level. Check for ground hazards such as holes, bumps and debris. Visually inspect the area above the equipment for aerial hazards like overhead power lines. Any of these hazards can really compromise the operator's safety and nearby employees, in addition to other structures and machinery on site.
MEC: MEC Scissor Lifts Canada - Safety Requirements for Scissor Lifts According to both OSHA and HRSDC, scissor lifts or "movable scaffolds" are industrial machines capable of lifting heavy and large cargo that are well balanced. They are responsible for transporting workers and their materials to and from high elevations efficiently and safely. Because these mobile heavy equipment are categorized as heavy machinery, there are numerous safety standards that apply to the maintenance and use of scissor lifts. Movement Scissor lifts sit upon a wheeled base so they could move around to access a wider variety of places. These pieces of equipment have been designed to move heavier cargo, equipment and even employees up and down to work areas. For safety reasons, workers are not permitted to ride on a scissor lift during the relocation process. Usually, this is to help make certain that no one falls from the machinery while it is being utilized. All staff working around a scissor lift as well as directly with the machinery must be informed regarding its movement prior to the driver releasing the safety brake in order to make the lift move. Constant communication around heavy equipment helps keep the working place and all individuals in it safe. Fall Protection There are several strict safety rules to follow regarding the safety standards for the scissor lifts in order to make certain that workers do not fall from the lift when they are using it. Even though scissor lifts are not required to be enclosed, there are features such as guard rails positioned around the lift perimeter in addition to a lock that has to be engaged on the lift platform entrance whenever the lift is being used. There are also slip guards in position for added safety. One more good safety habit workers should make is ensuring that heavy cargo or anything on the lift platform is fastened down in a secure way prior to moving the lift to be sure that nothing causes anybody on the lift platform to become injured.
Wolff: Wolff Tower Cranes Canada - In the year 1861, the company Harland and Wolff was established. Mr. Gustav Wilhelm Wolff, born in Hamburg during 1834, together with Mr. Edward James Harland born in the year 1831, formed the company. During the year 1858 Harland, who was the general manager during the time, purchased the small shipyard on Queen's Island. He bought the property from Robert Hickson, who was his employer. Harland at one time purchased Hickson's shipyard and made his assistant Wolff a partner in the business. Gustav Wolff was Gustav Schwabe of Hamburg's nephew. He has invested mostly in the Bibby Line. The initial 3 ships that the brand new shipyard built were for that line. By being innovative, Harland made the business a successful venture. Amongst his well-known suggestions was increasing the overall strength of the ship by replacing the upper wooden decks with iron ones. As well, he was able to increase the capacity of the ship by giving the hulls a squarer cross section and a flatter bottom. The company eventually faced increasing pressures in the shipbuilding industry causing them to shift their focus and broaden their portfolio. They chose to concentrate less on shipbuilding and more on structural design and engineering. The company also diversified into the areas of ship repair, offshore construction projects as well as competing for additional projects which had to do with metal engineering or construction. Harland and Wolff had other interests, such as a series of bridges to be constructed in Britain and in the Republic of Ireland. These bridges comprise the restoration of the James Joyce Bridge and Dublin's Ha'penny Bridge. During the 1980s, with the building of the Foyle Bridge, their first venture into the civil engineering sector took place. Today, the last shipbuilding project of Harland and Wolff was the MV Anvil Point. This was amongst six almost identical Point class sealift ships that was constructed to be utilized by the Ministry of Defense. The ship was launched during 2003, after being constructed under license from Flensburger, Schiffbau-Gesellschaft, shipbuilders from Germany.
Toyota: Toyota Forklifts Canada - Forklifts were initially made almost 100 years ago, and were once just simple machines which were manufactured to move pallets from one location than another. Advanced forklifts these days, are now offered in many designs, weight capacities, lifting heights and load capacities. These forklift units come with a wide range of ergonomic designs and enhanced safety features particularly designed for operator comfort. Perhaps the only common features of the diverse forklift selection are the tires used to move the machinery and the forks used to lift cargo. Counterbalanced Lift Trucks The Counterbalanced Lift Trucks include IC or Internal Combustion Trucks and also Electric Trucks. Narrow-Aisle Lift Trucks Narrow-Aisle Lift Trucks are available in various models such as: Reach trucks, Orderpickers and Turret Trucks. Pallet Jacks or Low Lift Pallet Trucks Low Lift Pallet Trucks or Pallet Jacks includes electric-powered pallet jacks and hand powered pallet jacks. Counterbalanced Trucks The forklift is the most popular type of lift truck and the most widely utilized of these is the sit-down, counterbalanced truck. A weight situated in the rear of all trucks ensures that the truck doesn't tip forward since it counterbalances the load's weight. Normally, a Counterbalanced Forklift Offers: Nearly all counterbalanced lift trucks provide a lift height more than 16 feet. The most popular units have a lift height of 189 inches. Offering a capacity ranging from 4000 pounds to 6500 pounds is among the most popular units. These machinery are offered with safety features like backup alarms and lights, amongst other items to guarantee safety of the operator. The counterbalanced lift trucks are typically powered by either internal combustion engines or electric motors. According to Jeff Rufener, President of the ITA or Industrial Truck Association, the split is approximately 60% electric, and 40 percent IC. He is also the Vice President for Mitsubishi Caterpillar Forklift America. There is certainly a lift truck available to meet your specific requirements. The electric units are perfect for warehousing, indoor applications, where potential fumes and noise are an issue. The IC units are great for outdoor, heavier lifting capacities and rougher terrain locations. Depending on the type of environment you will be working in, as well as what you will lift and be transporting, there is certainly the perfect Toyota lift truck available for you.
Yale: Yale End Control Forklifts Canada - The Cushion Electric Rider forklifts from Yale have earned a great reputation for providing outstanding performance and great value.Yale's drive motors are made to bring optimal performance, efficiency and dependability. Yale masts feature inventive engineering for amazing visibility and solid construction. All models will have microprocessor based control boards. This technology interfaces with all of the forklift systems, providing real-time truck status, full diagnostic capabilities and programmability for specific applications that ensure smooth transition, smooth drive and high effectiveness. Each sit-down rider forklift and stand-up rider has lift truck components which are engineered for extended, low-maintenance life and great performance. All the ergonomic specifications and comfort features that you require have been added to Yale's Narrow Aisle Lift Trucks. Yale designs and makes narrow aisle forklifts that are both industry and application specific. Yale drive motors are application proven for superior efficiency and overall dependability and excellent performance. Yale Hi-Vis masts incorporate innovative engineering for solid construction and unmatched visibility. In order to operate particularly for maximum storage density, very narrow aisles lift trucks are designed. The very narrow aisle lift trucks designed by Yale are ideal for pallet handling and case picking with applications varying from 16 feet to 55 feet. Yale spotlights the NTA for high density warehousing which uses maximum throughput. Yale has many motorized-hand trucks that offer great performance and value. These machines could be used in various industries. Yale engineers and designs a vast array of pallet trucks, platform trucks, walkie and rider units, stackers and tractor trucks for many different applications and industries. The drive motors designed and engineered by Yale have a proven track record for dependability, efficiency and performance. Each hand truck and its components are made for outstanding performance. These forklifts are made for low maintenance, extended performance. The easy-to-use handle has been specifically made with advanced ergonomics to enhance operator comfort. These handles contribute to better productivity because the operator is more comfortable. The motorized hand trucks manufactured by Yale have earned a solid reputation for providing exceptional quality and outstanding excellence within the material handling industry. Yale offers a huge variety of forklifts suitable for different applications. If you are looking for a new piece of heavy machine, but have to find out exactly what model would be the most suitable, visit your local Yale dealer and they would be glad to assist you. It is important to know what kind of places you would be utilizing the equipment and what type of loads you would be carrying. With all these integral parts of information, the dealer would be able to recommend the most suitable unit.
Skyjack: Skyjack Straight Man lifts Canada - Man Lift Designs Available nowadays, there is a huge array of articulating lifts, with many kinds of lifts to fit every application, circumstance and work place. There are certain manufacturers who specify in lifts for dangerous settings such as petro-chemical plants, underground tunnel situations, and other venues where there is a danger of explosive gases or dust, for instance in grain-processing plants. Some lifts have been mounted to large flatbed trucks or onto trailers or onto the back of a pick up truck. There are models which include articulating booms which can be self-propelled and are controlled by the lift operator, whereas others can pivot 360 degrees. There are outdoor and indoor lift models. They come in both 4-wheel and 2-wheel powered options. In some cases, the platforms are adjustable and several models have baskets where the employee stands. These baskets or platforms are adjustable and allow the workers to remain level or swing into place, depending upon what the operator should finish the job. There are different types of baskets and platforms which come wired so as to allow the operator to plug tools in as required. Skyjack Reconditioning The company SJ-Recon totally reconditions both Skyjack Electric Scissors and Rough Terrain, along with a selection of other boom lift models from various OEM's Skyjack Corporation. Reconditioning Method Before disassembly, each and every machine is thoroughly checked with all updates and outstanding safety bulletins completed. Moreover, all weldments on the machinery are thoroughly inspected for defects. These parts are carefully prepped before the painting process. The Recon Division at Skyjack has all the required equipment to offer a quality paint job. They provide a state-of-the-art blast booth and a complete paint line, and a professional oven.
Pecco: Pecco Tower Cranes Canada - Different KInds of Crawler-Mounted Cranes Industrial wheel tractors during the 1920s, including those built by McCormick-Deering and Fordson were quickly modified in order to be able to power a huge range of equipment. For instance, half-swing shovels and cranes were made by some companies around the engine and power train of the tractor and the wheels became replaced by crawlers. During the 1930s, crawler tractors came into widespread use. Immediately after, many manufacturers began manufacturing attachments for them, like various lifting machine devices. Side-mounted booms for example, were utilized primarily for pipe-laying at first and the machine got the nickname "pipelayer." These kinds of machinery are frequently utilized today for attending to cleaning up railroad derailments. Due to their size, compact design and mobility, along with outstanding lifting capacity, these types of machines are ideal for this use. In addition, swing booms that mounted on top of the engine compartment became available also. Crawler cranes are similar to the crawler tractor in that it travels along crawler tracks. These machinery could not move fast due to their intense weights. Normally, the crane is powered by one engine and may be controlled by 2 or more cable operated drums. The crawler cranes come outfitted with a lattice boom or a telescopic arm which is easy to extend by using hydraulics. The lattice boom should be manually assembled by adding multiple sections. Tower Cranes Typically found in big construction projects, tower cranes are required to be erected and broken down on location. They should be transported by truck every time they are relocated. These tower cranes are very tall. They enable construction crews to transport heavy steel or concrete building parts to the tops of tall buildings. Tower cranes utilize a hydraulic system to be able to push every new crane section up into place and thus, are self-erecting.
Case: Case Rough Terrain Forklift Canada - Case machinery are amongst the fastest machinery within the business and offer zero tail swing and an ease of operation. These lift trucks are made to handle the most difficult rough terrain environments head-on. The durable engine and rugged powertrain surpass the tractive force necessary to work on hillsides or in the mud. Smooth load control and minimal chain stress provide easy operation of the machinery. The harshest lift-and-carry applications and the roughest off-road material handling applications need a comfortable and durable forklift to finish the job. Case G Series 3 rough-terrain lift trucks offer superb operation in even the worst settings. There are 2 heavy-duty units to pick from, the 586G and the 588G to suit your material handling needs. Comfort and Control - The G-Series by Case offer 3 ideal machines for working long hours on the job. They provide entry from either side into the operator's compartment, a choice of seats and controls which are easy to use. Load control is one more available feature that provides smooth operation and minimal chain stress. These items offer a reduced maintenance cost. Superior Visibility - The tapered hood and the wide-channel dual-mast cylinders help to offer better operator visibility for safer and more efficient material handling on the job. The low profile design of the Case lift truck is compact as well and this feature adds to the overall stability of the machinery. Outstanding Maneuverability - Whether you are handling big cargo in narrow or tight spaces and require the muscle of a standard, full-sized lift truck, Case has the best alternatives for you. The 588G and the 586G both provide a narrow turning radius with their 55 degree axle turn angle. These machinery offer a maximum width of 2.24m or 88 inches and also have zero tail swing. Impressive Lift Speed - Case provides 3 lift trucks in their G-Series that have earned the reputation for being amongst the fastest within the business. They provide a maximum lift speed of 105 feet or 32m per minute, allowing you to become much more productive during your work day. Ease of Maintenance - There is no one else within the business who does service and maintenance better than Case. Overall production is very much better with the design of ground-level service access which has been designed and engineered on the Case G Series 3 forklifts. Like for example, the self-adjusting wet disc brakes and the roller mast design increase component life and lessen maintenance cost.
Advance Nilfisk: Advance Sweepers Canada - The parent company of Nilfisk is Northern Kabel and Telegraph or NKT for short. Copenhagen, Denmark is where there company has its headquarters. NKT is a 100 year old public company which specializes in manufacturing switching devices, cables and fiber optics. Their company hires 5,000 people every year. There are many different models of maintenance machinery and floor cleaning equipment advertised through a worldwide distribution network. Nilfisk-Advance has production facilities situated in Denmark, the United States, Sweden and Italy. The Nilfisk-Advance equipment that are sold include: Kent, Pulimat, Euroclean, Advance, Gerni and Nilfisk brands. These equipment are sold all around the globe in 80 nations, like North America and South America, Australia, New Zealand and the far East. The South African, Middle East and European marketing and sales activities are managed through a vast team of Nilfisk-Advance subsidiaries. Advance Sweeper-Scrubbers mesh high-performance debris-collection systems with powerful scrub decks. Scrubbing and sweeping in a single pass will basically cut in half the time spent utilizing separate machines. You would basically be able to double your floor cleaning production. Every equipment is capable of scrubbing and sweeping in just one pass. This equipment is very convenient because it provides the same level of cleaning in almost half time. The ergonomic operator compartments offer lots of safety and comfort. One-Touch electronic function controls are conveniently situated for easy and safe use of the model. Durable parts, along with rugged construction ensures years of dependable performance. These sweepers are made with open access to all key systems so as to facilitate easy maintenance. Clear views of key sweep zones are provided by Clear-View design. Machines built by Advance have been engineered to deal with to toughest tasks. For instance, when sweeping heavy debris, these machinery can swallow debris the size of a 2L bottle without harming the pavement underneath. The heavy-duty Advance sweeper units will target even your most difficult challenge. Any time you need to depend on a sweeper, be certain to select an Advance model that could offer you low maintenance and extreme productivity. Dependable performance is delivered by various rugged components. These mechanical sweepers are capable of suppressing dust across the whole sweep path, which is an excellent feature you would certainly come to be thankful for. These machines are comfortable, easy and safe to use. They are loaded with various safety features designed to protect bystanders, machinery and set up to protect the user.
